Experimental data for concrete masonry walls

by M. Hatzinikolas

Publisher: University of Alberta, Dept. of Civil Engineering in Edmonton, Alta

Written in English
Published: Pages: 126 Downloads: 961
Share This


  • Concrete walls -- Testing.,
  • Masonry -- Testing.,
  • Concrete masonry.

Edition Notes

Statementby M. Hatzinikolas, J. Longworth and J. Warwaruk.
SeriesStructural engineering report ;, no. 71
ContributionsLongworth, J. joint author., Warwaruk, joint author.
LC ClassificationsTA660.W3 H38
The Physical Object
Pagination126 p. :
Number of Pages126
ID Numbers
Open LibraryOL4200330M
LC Control Number80479377

A new edition of a well-known and respected book. This book provides a thorough guide for structural engineers on the use of concrete masonry. The second edition of the Concrete Masonry Designer's Handbook is the only handbook to provide information on all the new CEN TC masonry standards, as well as detailed guidance on design to Eurocode 6. masonry shear walls and for masonry foundation walls is also 8 in. ( mm). Note that the IBC allows shear walls of one-story buildings to have a minimum thickness of 6 in. ( mm). Lateral Support Lateral support for walls can be provided in the horizontal direction by cross walls. long test walls, the experimental data indicated that walls behaved in a one-way fashion, with no significant variation in deformation along wall length (i.e. in the horizontal direction). Walls were thus modeled similarly to a plane-strain model in which length of the wall is represented by a unit-length stack of CMU blocks, as shown in Figure 1. experimental data of masonry prisms using concrete blocks specifically designed for this purpose. The elastic and inelastic parameters were acquired from laboratory tests on concrete and mortar samples that constitute the blocks and the bed joint of the prisms. The results from the.

EMPIRICAL DESIGN OF CONCRETE MASONRY WALLS Keywords: allowable stress, anchorage, bonding, building codes, empirical design, height/thickness ratio, intersecting walls, lateral support, nonbearing wall, parapet, partition walls, shear wall, unreinforced concrete masonry, vertical loads, wall ties INTRODUCTION Empirical design is a procedure of proportioning and siz- ing unreinforced masonry. The experimental results demonstrate the effectiveness of FRCM strengthening on improving the shear capacity of masonry walls. Experimental data from other research programs using fiber reinforced polymer (FRP) composites are presented to demonstrate that when the normalized shear capacity is related to a calibrated reinforcement ratio, the two. @article{osti_, title = {Experimental Data and Guidelines for Stone Masonry Structures: a Comparative Review}, author = {Romano, Alessandra}, abstractNote = {Indications about the mechanical properties of masonry structures contained in many Italian guidelines are based on different aspects both concerning the constituents material (units and mortar) and their assemblage. This study discuses the development of a procedure that can be used to assess the reliability of concrete masonry unit infill walls subjected to personnel-delivered blast loads. Consideration is given to maintain reasonable computational effort for both the structural analysis and reliability models. Blast load and wall resistance models are developed based on experimental and analytical data.

  A study was recently conducted under the ATC project to examine available experimental data, evaluate the adequacy of these backbone curves, and develop improved guidelines and nonlinear models for the performance assessment of reinforced masonry wall structures. Both flexure-dominated and shear-dominated wall components were considered. When I was searching for a masonry book, I did not know what content was presented in this textbook so here is the table of contents: 1. Reinforced Concrete Masonry Materials 2. Masonry Assemblage 3. Allowable Stress Design 4. Strength Design 5. Deflection of Horizontal Masonry Members 6. Rigidity of Shear Walls 7. Anchorage to Masonry 8 Reviews: 1. - internal partition walls, according to the light character of the units; - walls of industrial, store and agricultural buildings; - freestanding masonry boundary walls. Specifities of lightweight concrete for masonry blocks The production of concrete for the manufacture of masonry units is . 10th Canadian Masonry Symposium, Banff, Alberta, June 8 – 12, EXPERIMENTAL STUDY ON HOLLOW BLOCK MASONRY WALLS FILLED WITH FOAMING CONCRETE Y.H. Ye1, W.M. Sun2, L.Q. Li3 and H.J. Zhang4 1Associate Professor, Dept of Civil Engineering, Nanjing University of Technology, Nanjing, [email protected] 2Professor, Dept of Civil Engineering, Nanjing University .

Experimental data for concrete masonry walls by M. Hatzinikolas Download PDF EPUB FB2

Experimental data for concrete masonry walls (Structural engineering report) [Hatzinikolas, M] on *FREE* shipping on qualifying offers.

Experimental data for concrete masonry walls (Structural engineering report). In this chapter, concrete masonry unit (CMU) walls subjected to blast pressure are analyzed with the finite element method, with the goal of developing a computationally efficient and accurate model.

Computational results are compared in the chapter to high-speed video images and debris velocities obtained from experimental by: 1. An innovative system for reinforced concrete masonry walls based on the combination of vertical and horizontal trussed reinforcement is proposed.

The mechanical characterization of the seismic behavior of such reinforced masonry walls is based on static cyclic tests carried out on panels with appropriate by: The investigation of concrete masonry walls demonstrated that the addition of carbon fiber reinforced polymers can increase the resistance to blast loads, but may result in a brittle failure mode.

The study of reinforced concrete walls showed that frangible panels can Cited by:   Experimental results available in the literature are used in this study.

The whole data set, composed of test specimens (Table 3 and supplemental data file), includes different types of frame-infill regard to reinforced concrete frames, both infilled frames and confined masonry structures are initially by: 8. The main objective of the study is to investigate the effect of partial infill walls on collapse mechanism of reinforced concrete (RC) frames using finite element models and experimental data.

Wall ties Concrete infill and grout Reinforcing and prestressing steel 3 Masonry properties Horizontal movements in masonry walls Vertical movements in masonry walls Notation BS building. In practice, the basic data and methodology for structural design in a given material is contained in a code of practice.

fastenings to concrete and masonry structures Modern fastening techniques are increasingly being used to transfer loads into concrete and masonry structures. In spite of this fact knowledge of the behaviour of such systems is very limited and there is no generally accepted design method.

One of the reserves for reducing material consumption, energy consumption, labor costs, and cost of the above elements is to improve the methods of their calculation and construction.

The results of experimental investigations of masonry and reinforced masonry walls under one-sided central and edge loading are presented.

estimating the flexural resistance of concrete and masonry components is based on current codes and guidelines (ACI and ACI R). Experimental data from previous shock tube tests on concrete and masonry walls retrofitted with FRP were used to validate the. This study deals with the identification of the mechanical behavior of chemical anchors embedded in masonry walls.

pull-out tests are carried out in five types of masonry walls built with clay brick or vertically perforated units with cement mortar. Different parameters are taken into account: embedment depths, masonry type, anchor position (injection either in brick units or in mortar.

Fastenings to Concrete and Masonry Structures, Comite Euro-International Du Breton Home Books Concrete Masonry Walls Structures. Fastenings to Concrete and Masonry Structures is reviewed, based on experimental results from various parts of the world.

The existing design approaches are compared with the available experimental data, and a. Using the acquired data from the experimental and analytical studies, effectiveness of GFRP rods as internal reinforcement for concrete masonry beams is demonstrated.

Read more Article. Book Description. Brick and Block Masonry - Trends, Innovations and Challenges contains the lectures and regular papers presented at the 16th International Brick and Block Masonry Conference (Padova, Italy, June ).

In an ever-changing world, in which innovations are rapidly implemented but soon surpassed, the challenge for masonry, the oldest and most traditional building material. with above-grade concrete masonry walls in non-traditional CMU markets; and • to identify different approaches to construction details, based on the two case studies in this report, between concrete masonry walls and other structural and non-structural members, including floor framing, gypsum wallboard, insulation, and window and doors.

Concrete and Masonry Movements provides practical methods for predicting and preventing movement in concrete and masonry, saving time and money in retrofitting and repair cost.

With this book in hand, engineers will discover new prediction models for masonry such as: irreversible moisture expansion of clay bricks, elasticity, creep and shrinkage.

Stone facing with Brick, Rubble or concrete Backing; Post-tensioned Masonry Wall. Post-tensioning provides an additional axial load to masonry structures and thus increases resistance to lateral force.

This type of walls has over their conventionally reinforced equivalents, such as increased in-plane strength and the absence of residual post.

The model is calibrated and validated against detailed experimental data obtained from tests on five moderately slender reinforced concrete wall specimens that experienced significant levels of shear-flexure interaction.

Read Book Analysis Of Masonry Wall Using Sap DESIGNING CONCRETE MASONRY WALLS FOR WIND LOADS - NCMA As the different studies have demonstrated, the nonlinear behaviour of the masonry walls is of great interest mainly where they are part of the building’s structural system.

In the present paper, an easy way. Reinforced concrete masonry wall is constructed by assembling of masonry units for example concrete block or bricks, mortars, reinforcing, and sometimes grout that is a kind of soupy concrete. In this article properties of materials employed in the construction of reinforced concrete masonry walls are discussed.

Contents:Properties of Materials for Reinforced Concrete Masonry Walls. Concrete masonry is used to construct various foundation wall types, including full basement walls, crawlspace walls, stem walls and piers.

Concrete masonry is well suited for below grade applications, because of its strength, durability, economy, and resistance to fire, insects and noise. The main contribution of this paper is to investigate both analyses (modal and static) of the reinforced concrete (RC) frame building during different construction stages, taking into consideration the effect on the modeling masonry infill (MI) and plastering brick walls, as well as a comparison between experimental and analytical results of.

Concrete and masonry performance characteristics Formwork Reinforcement Accessories Construction procedures Site and landscape elements Residential foundations Cast-in-place concrete Precast and prestressed concrete Tilt-up concrete Single-wythe masonry walls Multi-wythe masonry walls.

massive walls had about three to four times lower R-value than wood-framed walls (wood-framed wall R-value was about R vs. R-2 to R-5 for adobe, concrete masonry, and log walls). This gives a completely different meaning to the 5% energy savings that were reported.

During the years toChristian monitored an. For the case of clay brick masonry wall, the end point for the FEA is determined defining a discontinuity surface between two brick units along the thickness of the mortar.

The maximum tensile strain can be found as Load-displacement curve obtained from NLFEA and experimental data is given in Figure   Brick and Block Masonry - Trends, Innovations and Challenges contains the lectures and regular papers presented at the 16th International Brick and Block Masonry Conference (Padova, Italy, June ).

In an ever-changing world, in which innovations are rapidly implemented but soon surpassed, the challenge for masonry, the oldest and most traditional building material, is that it can. lintels, out-of-plane walls, plain concrete masonry, reinforced concrete masonry, shear walls, single wythe walls, software, strength design, structural design, walls specified by the user and may be off-center when an increase in effective depth is desired, such as for retaining wall.


Unreinforced masonry walls are extensively used in the petrochemical industry and they are one of the most vulnerable components to blast loads. To investigate the failure modes and improve the blast resistances of masonry walls, four full-scale field tests were conducted using unreinforced and spray-on polyurea-reinforced masonry walls subjected to gas explosions.

The book is divided into six chapters. from the physical and mechanical properties of reinforced concrete block masonry (such as a variety of strength index. modulus of elasticity. drying shrinkage. expansion coefficient. creep coefficient. etc.) to the structural design principles (such as temperature expansion joints maximum distance.

control. Concrete Masonry Handbook for Architects, Engineers, Builders William C. Panarese, Steven H. Kosmatka, Frank Alfred Randall Portland Cement Association, - Concrete construction - .SECTION 1 GENERAL The increased use of concrete and masonry walls for commercial and industrial buildings is due principally to their economy, fire safety, architectural appearance, and ease of con- struction.

Along with this increased usage, there has been a trend toward making these walls more slender in the interest of further cost savings. The proper design of these walls for strength and.Concrete Masonry andoo 1 1 Principal Differences between Blockwork and Brickwork Masonry is the word used to describe walls built out of masonry units laid on a mortar bed.

Masonry Units are commonly called: ksBloc (which are generally large hollow units) and; icks Br (which are smaller units, either solid or with small cores).